The airless sprayer is actually a relatively advanced spray method. During the operation, we recommend that you follow the slogan on the instruction manual. For example, make sure that the suction tube and the return tube are connected to the correct position and fixed tightly. Use the meter to measure the voltage to determine the voltage of 200-250 volts, check the leaking phenomenon of all parts of the equipment, etc. Let's take a closer look!
Step 1. Before we plug in the power, we recommend that you perform the following four steps:
1. We must first make sure that the suction tube and the return tube are connected to the correct position and fix it tightly, and then tighten the 15-meter long high-pressure paint hose to the other end of the paint tube.
2. Control the pressure control valve to a position without pressure (if the machine is rotating counterclockwise)
3, need to set the power switch to "off" position
4, at the same time do not forget to drop 5-6 drops of oil at the oil inlet
Step 2: We can first measure the voltage with a universal meter and then determine the voltage of 200-250 volts.
Step 3: Connect the power cord to at least the spray zone 7.
Basically, if it is on a 5 meter grounded power supply, then we can place the device in a well-lit area, and in many cases, in order to prevent overspray, free particles in the air are drawn into the device. Spray experts recommend that you use plastic canvas to isolate the spray area, and the power extension cable should not be too long.
Step 4: After we have reconciled the paint according to the recommended parameters of the paint supplier, we can use the filter to filter the paint and impurities in the paint, and often the impurities in the paint and The lacquer piece will block the rigid body and even cause damage to the equipment in severe cases.
Step 5, we need to put the suction tube and the return tube into the paint bucket, and also need to pay more attention to the return valve is set at the reflow position (counterclockwise rotation)
Step 6. Basically, we all need to turn on the power of the device and slowly pressurize the pressure control knob to the middle pressure zone to allow the paint to circulate in the device until all the air in the device is discharged from the return pipe.
Step 7. We can hold the gun handle first and then open the gun insurance. However, it is necessary to pay attention to the fact that the gun must be pointed at the wall of the paint bucket and the trigger is tightened. At the same time, the return valve is tightened. The paint is ejected from the muzzle until all the air in the paint tube and gun is expelled, and the pressure is maximized after it releases the trigger and closes the gun fuse.
Step 8. Before use, the experts of Transon suggest that you can check whether there are any leaks in all parts of the equipment. If there is any, then it is recommended that you follow the â€œpressure relief procedureâ€ to release the pressure and then tighten the leaking part.
Step 9. In many cases, if there is no dripping, then we can turn off the power switch, but we need to pay more attention to the fact that the return valve must be placed at the return position to release the pressure.
Step 10. Under normal circumstances, if the gun insurance is closed, it is recommended that you can install the nozzle and nozzle sheath on the spray gun and tighten it. Of course, we can also turn on the power switch and return the return valve. Tightening the hour hand, deducting the trigger and observing the spray, slowly increasing the pressure until the web is completely atomized.
Concerned about surprises
Label: paint spray frame spray machine power switch tube
Previous: Working principle of powder coating electrostatic spraying equipment Next: Air spraying coating method
20W Glue Guns Features:
4. Proective Nozzle Cover
5. Trigger Flow Control
6. Bonds instantly
7. High quality
8. High temperature or low temperature
9. New design
10. With switch function
Idea for many applications. Fastening various materials such as paper, cardboard, fabric,wood, lace,trims,leather,metal,glass, tiles, rubber, ceramics and flooring etc.Ideal for hobby and household repair,DIY&craft projects.
Designed and manufactured to the highest of standards to ensure a robust and long life, we hope it provides you with many years of trouble-free, safe and reliable service.
1ï¼Ž Before use the glue gun, check if the plug cord into electrical outlet properly;
2ï¼Ž When glue gun in first use, the heating element will have small smoke, it is normal situation, but the smoke will disappeared after 10 minutes;
3ï¼Ž After power, not for a long time in standby mode(not longer for 20 minutes), when the suspension of use, unplug first.
4ï¼Ž Avoid to use the glue gun under very hot or very cold environments.
5ï¼Ž Better not work under direct cold wind blowing, it will reduce efficiency and loss power
6ï¼Ž When in continuous using, do not press the trigger with great pressure, and try to squeeze out the un-melted glue, it would damage the glue gun
7ï¼Ž Not applicable for bonding heavy objects or objects needed strong adhesive
8ï¼Ž The quality of glue stick will directly influence the glue gun function and sticking objects quality;
9ï¼Ž If the power cord is damaged, do not replace it by yourself, must ask for professionals to replace it.
10ï¼Ž This tools must b e placed in its position when not in use. And storage before the tools complete cooled.
11ï¼Ž Be careful when using any other electrical appliance with flammable material.
12ï¼Ž Not applicable for a long time in the same place.
13ï¼Ž Do not use an explosive gas atmospheres.
14ï¼Ž Note that heat may be the line of sigh, combustible materials.
15ï¼Ž Do not leave equipment unattended when switched on.
16ï¼Ž This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
17. Children should be supervised to ensure that they do not play with the appliance.
1. Glue gun using voltage is 110-220V AC,50/60Hz;
2. Tip gun forward on stand and place a piece of cardboard under the nozzle
3. Use 7-8mm (mini trigger glue gun), 11-12(big trigger glue gun), insert glue sticks through
tunnel at back of gun
4. After power, wait for 5-10 minutes to allow glue to softenAfter glue softens, squeeze trigger to feed glue through glue barrel. Excessive force will damage glue gun. Put down nozzle after work, disconnect the power plug
20W Glue Guns, 20W Mini Glue Gun, Regular Glue Gun
Ningbo Kingvos Electrical Appliance Co.,Ltd , http://www.kingvos.com