Seven strokes to solve the paint problem

Jc001.load('iframe') JIFrame.create({ 'url' : '/go.php?action=ads&iframeHeight=250&isIframe=1&key=%CD%BF%C1%CF&pos_id=jc001_news_detail_30&reqkey=1&style=margin%3A15px+15px+ 25px+0%3B+height%3A255px%3Bwidth%3A255px%3B+float%3Aleft%3B', 'height' : 250 })

Paint is an important part of the interior decoration, and it is easy to have some difficult problems, which makes people feel helpless. In fact, as long as we find out the real cause of the problem, it is not difficult to have satisfactory results. The following is a solution to the problems that are easy to produce, so that you can be more comfortable in interior decoration.

Peeling paint

It may be because the surface is too smooth. If the original paint is lacquered or powdery (with an untreated paste coating), the new paint will not stick to the surface. Or it may be wood decay or metal rust spots, but also peeling off due to poor paint quality.

A small area of ​​paint peeling off, first sanded with fine sandpaper, then put on putty, brush the primer, and then repaint. Large areas of peeling must be scraped off and repainted.

Paint blistering

First of all, the bubble is broken, if there is water, it means that there is moisture infiltration under the paint layer or behind the sun. After the sun shines, the water evaporates into steam, which will make the patent leather foam. At this point, the hot air spray gun is used to remove the foamed paint, the wood is naturally dried, then the primer is applied, and finally the entire repair surface is repainted.

If there is no water in the bubble, it may be cracked in the wood grain, and there is a small amount of air inside. After the sun shines, the air expands and the patent leather bulges. In the face of this situation, first scrape off the foamed patent leather, then fill the crack with the resin filler, repaint, or do not use the filler, after scraping off the patent leather, directly apply the microporous paint.

Crack

In this case, it is mostly necessary to remove the paint with a chemical paint remover or a hot air spray gun before repainting.

If the fracture range is not large, you can use sanding block or wet and dry sandpaper to wet the water, grind off the broken paint, after the surface is smoothed, put on the putty, brush the primer, and repaint.

Paint hooligan

If the paint is too thick at a time, it will cause runny. If the paint is not dry, brush it with a brush. If the paint has begun to dry, wait until it is dry. Smooth the surface with fine sandpaper, clean the surface, wipe it with a damp cloth, and then re-apply. The outer layer paint, be careful not to brush too thick.

Stains

There are many reasons for stains on the paint surface. For example, the water in the latex paint dissolves the material on the wall and rusts the paint surface. The wall surface rubbed with steel wool will produce rust spots, and the dark pipe in the wall will leak and appear stains. To prevent stains, first apply a primer containing aluminum powder. If stains have appeared, remove the latex paint from the stains, brush the primer containing aluminum powder, and then repaint.

Moldy discoloration

This problem occurs mostly on wet paint surfaces, such as water vapor condensation on glass or metal surfaces, often producing brownish black stains. At this point, the fungicide can be used to treat the moldy parts according to the instructions of the instructions. After the mold is killed, the surface is cleaned and then repainted.

Lost gloss

The reason is that the primer is not applied, or the primer and the inner layer paint are not dried, and the varnish is directly applied. As a result, the varnish is absorbed by the wood and loses its luster. The poor quality of varnish is also a cause.

Use old wet and dry sandpaper to rub off the old paint, brush off the dust, wipe the surface with a clean damp cloth, and then dry it again.

It is important to note that painting in a very low temperature environment may also result in loss of gloss after the film has dried.

Paint film wrinkling

Usually caused by brushing the second time after the first time the paint is not dry. At this time, the solvent in the undercoat affects the upper paint film and wrinkles it.

In this case, the creped paint film can be removed by chemical mercury removal or heating to repaint. Remember, you must wait until the first time the paint has dried out before you can go to the second time.

Paint rough

The newly painted surface is rough, usually because the paint brush used is not clean or contaminated by the surrounding environment. It is also possible that the paint is mixed with patent leather, which has not been precipitated and filtered before use, or that the paint is dusty when it is not dry.

To prevent this from happening, a clean paint brush and paint bucket must be used. Always filter with paint filter paper or clean nylon stockings before using the old paint. In addition, the painted surface should be covered with a cover or cardboard when the paint is not dry to prevent dust.

If the paint surface is rough, after it has dried out, smooth it with a dry and wet sandpaper, wipe it off, and then paint again. Pay special attention to the paint brush must be clean.

Dark spots appear on the surface of painted wood

It may be that the knot is not sealed before painting, and the sun is exposed to the sun, the knot is heated, and the resin is exuded from the knot. At this point, the paint can be scraped off with a spatula, and then polished to a wooden knot with a fine sandpaper, and the knot is sealed with a seal paint, and then repainted after drying.

Paint does not dry

If the room is not well ventilated or the temperature is too low, the paint will dry slowly. It is possible to open all doors and windows to promote ventilation, or to place a heater inside to increase the room temperature.

If the problem is still not solved, the painted surface may be greasy. This can be done by chemical paint remover or heat removal, thoroughly rubbing the surface and then repainting.

Painted on the worm

Try to remove the bugs when the paint is not dry, then use a brush to lightly polish the surface. If the paint has begun to dry out, wait until the paint film is completely hard and then wipe off the bug so that it does not make the surface messy.

Guanyu Bathroom is a Foshan, GD base manufacturer of reliable luxury bathroom fixtures such as bathroom furniture, steam showers, whirlpool bathtubs, stainless steel Shower Panel, acryllc Bathtub, shower cublcle and shower tray.

High Quality Acrylic Board Indoor Bathtub / Low-Noise Design Comfortable Freestanding Bathtub / Creepage Protection Design Luxury Bathtub


Why Guanyu???

There are lots of reasons to think Guanyu is the best luxury bathroom manufacturer in the world. Our Bathroom Furinture is manufactured using a high-density waterproof oak and all of our shower, steam rooms, whirlpool bathtubs are manufactured using a unique form superior acryllc that you will not find any of competitors products. All of our products are built from ground up for reliability. Once our products are manufactured, we perform more quality assurance that anyone else in the industry. Each unit is individually tested and hand inspected before it is shipped. We are so confident in the reliability of our products are healthy for the mind and body.

Our Mission: To provide outstanding bathroom products that our customers love for their reliablility, functionality, and style.


High Quality Acrylic Sector Bathtub

High Quality Rectangle Massage Bathtub

One Person Comfortable Function Bathtub

High Quality Human-Oriented Design Bathtub

Please kindly contact us for further details if you are interested, thank you very much!


Championship Bathtub

Championship Bathtub,Black Championship Bathtub,White Championship Bathtub

Foshan Guanyu Group , http://www.guanyu-group.com

Posted on